All best sellers
  • On sale!
  • Reduced price
Rolling Pin Frozen | Textured Rolling Pins
  • Rolling Pin Frozen | Textured Rolling Pins
  • Rolling Pin Frozen | Textured Rolling Pins
  • Rolling Pin Frozen | Textured Rolling Pins
  • Rolling Pin Frozen | Textured Rolling Pins

Rolling Pin Frozen


Rolling Pin Frozen

$13.80 Save 20%

100% secure payments

Rolling Pin Frozen 

Textured Rolling Pins capable of pressing a continuous repeated pattern on clay and putties. Made of clear PMMA plastic with amazing non-stick properties. Non-toxic. They come in several different textures that you can purchase based on your specific needs.

Length: 14'50 cm (5’5 inches)

Diameter: 2’5cm (1 inch)


1st - Properly mix the putty/clay until ready according to the manufacturer's recommendations.

2nd - Extend the putty/clay on a surface to be textured. For optimal results, make sure you have got a smooth and even surface before impressing with the Rolling Pins. *** We recommend using a plain Rolling Pin for this.

3rd - Depending on the type of putty/clay, it is advisable to wet the Rolling Pin to prevent any sticking.

4th - Slowly move the Rolling Pin applying equal pressure at all points for an even texture.

5th - Trim any excess putty/clay with a sharp knife. It is recommended to do this once it has dried to avoid any deformations in the putty/clay.


There are plenty of different putties and clays on the market and all of them can be textured using the proper technique.

Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these Rolling Pins as they allow for an easy correction of mistakes before they are baked. If the aim is to make textured bases, we recommend using MDF bases, because you can texture the polymer clay directly onto an MDF base, and then put it all in the oven, including the base. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood may leave a slight scent similar to that of toasted bread, but don't worry it won’t burn!

In the case of epoxy putties, there are a variety of techniques which achieve similar results. Good thing is. you do not need to bake them, so they may be applied directly onto plastic bases.

For Green Stuff putty, which is particularly sticky, it is required to slightly wet either the putty or the Rolling Pin with some water before texturing. You may also reduce the stickiness by applying talcum powder, or using Sculptor Vaseline (LINK).

Other epoxy putties like the Milliput putty, for example, are also suitable, but we wouldn't recommend to wet them much since it will hinder your work. Furthermore, if the mixture is too sticky, it is better to continue kneading until the stickiness is gone.

*** For this type of epoxy putties, it is very important to clean the rolling pins properly after use.


After working with the Rolling Pins, use a Scratch Brush (LINK) and plenty of water to clean off any residue on the Rolling Pins if required.


To ensure safety, children should be closely monitored by a responsible adult.  


Pantent number 002568469

Product Details

Very practical for basing minis

These pins are extremly practical for making a great vatiety of bases for wargame minis.
I used it for broken land and it's exelent.

I use epoxy resin and I recomend wetting the surface and using silicon spray mould release.


Love it!!

I have gotten this rolling pin in the 6 pack, and I must say, it does its job very well. it's a bit tricky to find the right amount of pressure (it takes more than you would think) but the results are fantastic. it can be both cracked ice or irregular stonework, and it works wonders for city tiles! I'm planning to use it to make sewers tiles. approved!


Easy use

It works really well to do a broken land, frozen lake or lava world. Easy to clean too.


Best Frozen effect ever

Easy and fast to use, a wonderfull way to make winter icy bases

Write your review

Rolling Pin Frozen

Rolling Pin Frozen

Rolling Pin Frozen

Write your review
You might also like
16 other products in the same category: