Textured Rolling Pins


Viewed products

Rolling Pin Double Diamond


New product

Rolling Pin Double Diamond

More details

With this product, you earn 12 loyalty point(s). 12 point(s) = 0,30 €.

12,00 €


15,00 €

Add to wishlist

More info

Rolling Pin Double Diamond

Textured rolling pins capable of impressing a continuous repeat pattern on clay and putties. Made of clear PMMA plastic with amazing non stick properties. Not toxic. They come in several different textures that you can purchase based on your specific needs.

Length: 14'50 cm (5’5 inches)
Diameter: 2’5cm (1 inch)
Pattern Size: 3x1 mm
Scale: 1/32-1/43-1/48


1st - Mix properly the putty/clay until ready according to the manufacturer's recommendations.

2nd - Extend the putty/clay on the surface to be textured. For better results, make sure you have gota n even and smooth surface before impressing with the Rolling pins. *** We recommend using a plain Rolling pin for this purpose.

3rd - Depending on the type of putty/clay, it would be advisable to wet the Rolling pin to prevent sticking.

4th – Move slowly the roll applying equal pressure at all points for a similar texture.

5th - Trim excess of putty/clay with a sharp knife. It is recommended to do this once dried to avoid the putty / clay is deformed.


There are plenty of different putties and clays on the market and all of them can be textured using the proper technique.

Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these rolling pins since they allow to easily correct mistakes till they are baked. If the aim is making textured bases, we recommend using MDF bases, because it would be posible to texture the polymer clay directly on MDF base, and then put everything in the oven, base included. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood will just leave a similar smell of toast bread but it won’t burn.

In case of epoxy putties, there are different techniques to achieve similar results. Good thing is that you do not need to bake them up, so they may be applied directly on plastic bases.

For Green Stuff putty, which is especially sticky, it would be required to wet either the putty or the Rolling pin with some water before texturing. You may also reduce the stickiness by applying talcum powder in the water, or even using Vaseline or oil.

Other epoxy putties like Milliput putty are also suitable, but we would not recommend to wet them much since it will hinder your work. Moreover if the mixture is too sticky, it would be better to continue kneading till stickiness is gone.

*** For this type of epoxi putties, it would be very important to clean the rolling pins properly after use.


After working with them, use a toothbrush and plenty of wáter to clear any residue from Rolling pins. To clean the most difficult dirt parts stuck in the rolling pin we recommend the use of the Scratch Brush Pens.   


To assure safety, children should be closely monitored by a responsible adult.  




Pantent number 002568469



Très utile

Il est clair que ça fait gagner énormément de temps pour les décors. Le rouleau est parfait avec des pâtes de bonne texture comme la Sculpey et la Miliput. Avec de la Fimo séchant à l'air, le résultat est assez moyen, mais ça peut servir pour casser des morceaux.
Je regrette juste que le rouleau ne soit pas entièrement couvert du motif diamant double pour faire des grandes plaques métalliques.

  • 1 out of 1 people found this review useful.

Almost perfect

I love the level of detail and how it looks when applied, it's simply amazing. Maybe if i were to be picky i'd say a bit more of a handle surface or something to make it roll easier would be great, but i guess it's more clay/putty focused than to be used on foam. Overall still pretty nice.

  • 2 out of 2 people found this review useful.

Write your review!

Write a review


Customers who bought this product also bought: